by Jax Media Team Jax Media Team

3 Common Mistakes When Trying to Repair Drywall

Drywall repairs can be a true pain in the neck if they’re done incorrectly. Luckily, errors are easy to avoid if you know what signs to watch out for. Here are three of the most common mistakes made when repairing drywall. 

Common Mistakes Made When Repairing Drywall

1. Over-sanding

Drywall may seem indestructible, but it can still become damaged from regular activities like vacuuming or children throwing toys around the room. Luckily, such damage is straightforward to remedy using an aircraft-type snip to cut away and replace any severed corner beads with new pieces before applying joint compound and sanding each coat to smooth the surface.

One common misstep when trying to repair drywall is over-sanding. This can be a costly mistake as it weakens and exposes your walls to future damage. An alternative solution would be using a light touch hand sander instead, though always wear a respirator when doing this to protect against inhalation of Gypsum and Silica dust particles; additionally, clean up after every session with a damp sponge to help minimize dust build-up on the walls as you work.

2. Hanging Drywall with Nails Instead of Screws

Drywall is attached to wall studs and ceiling joists using nails with long shanks and large heads known as drywall nails. Over time, however, those nails may lose their grip and pop through the surface – something which may happen due to shrinking wood framing, shifting in the home, or because it wasn’t driven solidly into either stud or joist. Nail holes may be repaired temporarily by tapping them back down with a hammer; however, this won’t solve the underlying cause.

Instead of replacing the nail that was lost through popping out, use drywall screws to reattach it back onto its frame in the area where the hole appeared. This can help stop future instances of pulling away from the wall due to tension from pulling drywall away again. To do this, locate any nearby studs and use screws designed specifically for drywall when driving screws into place.

Once the screws have been securely mounted, use a lightweight patching compound applied with a putty knife to fill and smooth over any new holes that have opened up. After drying, lightly sand the area with a sanding block to eliminate any rough patches and provide a seamless repair patch finish; finally repaint over it so as to hide its marks of sanding.

3. Applying Too Much Mud

Drywall repairs usually involve filling in dented, holes and cracks with mud. While smaller dings and scratches may be patched easily with lightweight spackling compounds and putty knives, larger holes and cracks require greater support as well as thicker fillers in order to achieve durable repairs that remain virtually undetectable.

Too much mud applied during drywall repair can create an unattractive bulge on the wall that can become easily visible and more susceptible to cracking over time. To avoid this scenario, try using a smaller tool for applying your mud instead of large brushes or sponges; it will allow for greater control in controlling how much is being applied across all sides and ensure even coverage.

Too much mud can also be hazardous because it traps moisture inside walls, leading to mold growth, mildew formation, and other serious health concerns that are hard (and costly) to address.

To avoid this scenario, always wait 24 hours for your mud to fully set before beginning to paint it. Additionally, it is a good idea to wait until humidity levels have decreased before starting your new drywall painting project since high humidity can cause wood framing to expand and contract which in turn results in cracks in your wallboard.

Make sure you avoid these three common mistakes made when trying to repair drywall, so that you don’t end up with bigger issues.

by Jax Media Team Jax Media Team

How Often Should You Pressure Wash Your Home and Why?

Homeowners in certain areas must contend with dirt, mildew, and mold growth on their property, making regular pressure washing essential to keeping it looking its best.

Not only does an unsightly exterior make your building less appealing, but it can actually wear away at certain building materials over time. Regularly cleaning roofs, gutters, and surfaces helps lower structural risk. Here are some factors to consider when deciding how often to pressure wash your home.

Weather

How much dirt builds up on the exterior of your home depends on local weather conditions. Mold and mildew flourish in humid environments while beach homes accumulate sand accumulation. Rain, wind, and debris also leave their mark by depositing dirt onto your house’s siding.

Pressure-washing your home should take place between spring and fall when temperatures don’t become extreme. Avoid pressure-washing under direct sunlight, when temperatures become extremely hot or when air becomes dry as this could damage surfaces such as wood.

If you live in an area with harsh winters, it’s a wise move to conduct two pressure washes per year – one before and one after winter seasons – in order to protect the exterior from mold and mildew growth and maintain its beauty. Winter provides an opportunity to remove debris collected from fallen leaves and branches that have collected in gutters or collected on surfaces like driveways and roofs.

Season

Homeowners may view pressure washing as an optional task, but it plays an integral part in many home projects. Paint cans, sealant tubes, and stain bottles all stipulate that a clean surface must be present prior to their application.

Pressure washing your property regularly not only enhances its appearance but also helps prevent the growth of harmful mold and mildew that could compromise building materials and cost thousands to fix down the line.

Springtime is an excellent time for pressure washing as weather conditions tend to be warmer, which enables deeper cleaning while helping surfaces dry more quickly afterward. Pressure washing also removes pollen and other allergens that may trigger respiratory problems in children and adults alike, and removes pollen that causes respiratory difficulties for some people. 

Fall also presents opportunities to power wash as leaves can accumulate moisture in your yard which promotes the development of fungus growth.

Materials

Power washing your property regularly can bring many advantages. Not only does it enhance curb appeal and extend roof shingle life expectancies, but also it protects other exterior materials such as vinyl siding.

Before hiring a professional to spray, move anything that may obstruct their work – such as patio umbrellas or soft material outdoor furniture – away from surfaces you want to be cleaned, such as an umbrella. In addition, remove or cover light fixtures, air conditioners, or electrical outlets that could become submerged by water spray.

Ask the professionals you hire what the optimal cleaning frequency should be, especially for certain materials like tile roof tiles that collect grime quickly or vinyl siding which is more prone to mildew and cobweb buildup. 

Also, keep in mind that certain materials require more frequent washing – tiles being one example where dirt builds up easily while cobwebs form easily on vinyl siding surfaces can warrant pressure washing more frequently as well as pressure cleaning more regularly if they feature these features.

Typically, pressure washing your home once or twice a year is plenty, but in some cases, you may want to do it more or less. Work with the right professionals and you can set up a regular maintenance schedule to follow for pressure washing.